Learning the Basics of Plumbing for Bathtub Installation
Learning the Basics of Plumbing for Bathtub Installation
Blog Article
This article down below involving How to Install a Bathtub is seriously fascinating. Read it for yourself and decide what you think about it.
Setting up a bathtub isn't exactly rocket science, yet it does need strong plumbing, carpentry, and sometimes, tiling abilities. Replacing an old tub with a brand-new one is also a reasonably difficult job. If the old bathtub is conveniently easily accessible, the task can move immediately; if you need to open a wall to eliminate the old bathtub and also place the brand-new bathtub, the task is much harder. In either situation, the job is within a house handyman's abilities, although you will certainly require an assistant to vacate the old bathtub and also set in the new one. See to it you have qualified yourself for the task and also fit attempting it. Rather than employing a service provider to take over a halfway-completed task, it is far better to take into consideration employing one before you begin. Chances are you might need a professional plumber to make tube links.
This write-up will help you set up a brand-new bathtub in your shower room if you have actually currently bought a brand-new bathtub and also don't need to change the setup of your previous water pipelines.
Your devices as well as material checklist ought to comprise the following:
Removing Old Taps
If you need to change old taps with new ones as a part of your installment, then the first thing you must do is disconnect the water supply. After doing so, activate the taps to drain any kind of water remaining in the system. The procedure of removing the existing faucets can be quite bothersome due to the restricted gain access to that is frequently the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the faucets. Have a cloth prepared for the continuing to be water that will originate from the pipes. Once the supply pipes have been gotten rid of, make use of the very same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single faucets from transforming during this procedure. When the taps have been gotten rid of, the holes in the bath/basin will need to be cleaned of any old securing substance.
Before proceeding to fit the brand-new taps, compare the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the brand-new taps to fit.
Suitable New Taps
If the tails of the brand-new faucets are plastic, after that you will require a plastic port to prevent damage to the thread. One end of the adapter fits on the plastic tail of the tap and the other end offers a link to the existing supply pipes.
If you need to fit a monobloc, then you will require reducing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next off, place the faucet in the mounting opening in the bath/basin ensuring that the washers are in place in between the faucet and also the sink. Secure the tap in position with the manufacturer supplied backnut. As soon as the faucet is securely in place, the supply pipes can be attached to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with typical faucet connectors. The former type should be attached to the faucet finishes first, tightening only by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Setting up the Bathtub
Using the two wood boards under its feet, put the tub in the needed position. The wooden boards are practical in uniformly spreading out the weight of the bath tub over the area of the boards as opposed to concentrating all the weight onto 4 small factors.
The next goal is to ensure that the tub is leveled all round. This can be attained by checking the level as well as changing the feet on the tub up until the spirit level reads degree.
To mount faucets, fit the bottom of the furthest adaptable faucet connector to the proper supply pipeline by making a compression join; then do the very same for the other faucet.
Turn on the water system and examine all joints as well as brand-new pipework for leaks and also tighten them if needed. Fill the tub and likewise examine the overflow outlet and also the typical electrical outlet for leaks.
Lastly, fix the bathroom paneling as described in the supplier's instruction manual. Tiling and also sealing around the tub needs to wait until the tub has actually been used at the very least once as this will settle it right into its final position.
Preparing for the Installment
To start with, the sustaining framework provided with the bath must be fitted (if called for) according to the supplier's guidelines. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is important to ensure that if the tap comes with a plastic washer, it is fitted between the bath as well as the taps. On a plastic bath, it is additionally sensible to fit a supporting plate under the faucets unit to prevent strain on the bathtub.
Fit the flexible faucet ports to the bottom of the two faucets making use of 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet with the hole in the bathroom. Utilize the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Make sure you utilize every one of the provided washers.
Attach the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath should now be ready to be suited its last position.
Tiling Around the Tub
In the area where the bath satisfies the ceramic tile, it is needed to seal the accompanies a silicone rubber caulking. This is essential as the fitting can relocate sufficient to crack an inflexible seal, triggering the water to permeate the wall in between the bathroom as well as the tiling, leading to difficulties with moisture and also possible leakages to the ceiling below.
You can select from a selection of coloured sealers to blend in your components and also fittings. They are sold in tubes as well as cartridges, and also are capable of securing voids up to a width of 3mm (1/8 inch). If you have a larger space to load, you can load it with spins of soaked newspaper or soft rope. Remember to always fill the bathtub with water prior to securing, to allow for the movement experienced when the tub is in use. The sealer can fracture rather very early if you do not take into consideration this motion before securing.
Alternatively, ceramic coving or quadrant floor tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally conveniently available on the marketplace. It is suggested to fit the tiles using waterproof or waterproof glue as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I came across that page about Installing A Bathtub while browsing on the web. Do you know another individual who is curious about Installing A Bathtub? Do not hesitate to share it. Many thanks for going through it.
Expertise at your service. Report this page